Go to body Contents
Index global

Construction Adhesives - Standard adhesive mortar, Adhesive mortar for a special insulation material

  • Payment
    L/C(sight) , OT , T/T
  • MOQ
    Negotiable
  • Supply Details

    Depend on quantity

  • Country of sale
    Asia, Americas, Europe, Middle East, World Wide
  • PRICE
    • FOB

      Depend on quantity

ITEM SPECIFICS

  • Brand
    Index global
    Model Construction Adhesives
  • origin
    Republic of Korea
  • Size(Capacity)
    Packing unit – (18 L): 22 kg±1/pl
  • Weight
    Amount – 2.2 kg/㎡ For the EIFS: 10 ㎡/pl
  • Function
    Construction Adhesives
  • Features
    EIFS and attachment of EPS boards
  • Gender
    All gender


PRODUCT DESCRIPTION

Standard adhesive mortar
Standard adhesive mortar (Base Coat), which is made of special, water-soluble acrylic resin, is an adhesive that is used in the EIFS, and it is suitable for attaching EPS boards or fiberglass mesh. It is usually mixed 1:1 with Portland cement.
• Packing unit – (18 L): 22 kg±1/pl
• Amount – 2.2 kg/㎡ For the EIFS: 10 ㎡/pl
 
Process (Attachment of EPS boards)
1. Mix adhesive mortar, cement, and water (1:1:0.08) using a 400–600 rpm hand mixer for about 1–2 min until the lumps disappear. The order of the injection (styrobond–cement–water) is important in increasing the mixing stability.
2. Basically, the mixture should be used within 1 hr, and about 2.5 kg per 1 ㎡ is appropriate. An attachment should be made before the surface dries.
3. During attachment, only a little force needs to be applied and the smoothness should be maintained.
 
 
Usage
EIFS and attachment of EPS boards
 
Note
1. If the surface is a new concrete wall or a mortared wall, check the curing condition of the surface (pH 7–9) before use.
2. Remove any dirt, grease, rust, or other foreign matters on the surface.
3. Smoothen bumpy or textured walls by using a grinder or a similar equipment, and remove at least 5 mm from the surface of the part where rust is likely to occur because of nails.
4. Protect the areas where mortar is not required with a masking tape or a plastic.
5. Stir the mixture thoroughly before using it, and make sure that the mixture does not get permeated with any foreign body from the container inlet.
6. Stir the mixture using a 400–600 rpm hand mixer for about 1–2 min in accordance with the mixing ratio and order until the lumps disappear. Be careful not to cause many air bubbles.
7. The mixture should be used within 1 hour and be protected from direct sunlight during summer. Hydration heat can accelerate the hardening of the mixture, which grants better schedule management.
8. An attachment should be carried out before the surface is dried, and the time can be adjusted depending on the ambient conditions. Once the surface starts to dry, the adhesion can be seriously decreased.
9. Apply the product to an appropriate area, and follow the process that was explained above.
10. Do not mix the product with other products.
 
 
 
 
Adhesive mortar for a special insulation materials (e.g., boards and mesh)
An adhesive mortar for a special insulation (e.g., PF boards and others) is an adhesive for special insulations or the EIFS, and it is suitable for attaching a special insulation or a fiberglass mesh. Two types of adhesive mortar (for board attachment and mesh impregnation) are separately provided, and they are mixed with Portland cement in a ratio of 1:1.
· Packing unit – (18 L): 23 kg±1/pl
· Amount – 2.3 kg/㎡ For the EIFS: 10 ㎡/pl
 
Process (Attachment of PF boards)
1. Mix adhesive mortar, cement, and water (1:1:0.08) using a 400–600 rpm hand mixer for about 1–2 min until the lumps disappear. The order of the injection (styrobond–cement–water) is important in increasing the mixing stability.
2. Basically, the mixture should be used within 1 hr, and about 2.3 kg per 1 ㎡ is appropriate. An attachment should be made before the surface dries.
3. During attachment, only a little force needs to be applied and the smoothness should be maintained.
 
 
Usage
EIFS and attachment of PF boards
 
Note
1. If the surface is a new concrete wall or a mortared wall, check the curing condition of the surface (pH 7–9) before use.
2. Remove any dirt, grease, rust, or other foreign matters on the surface.
3. Smoothen bumpy or textured walls by using a grinder or a similar equipment, and remove at least 5 mm from the surface of the part where rust is likely to occur because of nails.
4. Protect the areas where mortar is not required with a masking tape or a plastic.
5. Stir the mixture thoroughly before using it, and make sure that the mixture does not get permeated with any foreign body from the container inlet.
6. Stir the mixture using a 400–600 rpm hand mixer for about 1–2 min in accordance with the mixing ratio and order until the lumps disappear. Be careful not to cause many air bubbles.
7. The mixture should be used within 1 hour and be protected from direct sunlight during summer. Hydration heat can accelerate the hardening of the mixture, which grants better schedule management.
8. An attachment should be carried out before the surface is dried, and the time can be adjusted depending on the ambient conditions. Once the surface starts to dry, the adhesion can be seriously decreased.
9. Apply the product to an appropriate area, and follow the process that was explained above.
10. Do not mix the product with other products.

PAYMENTS DETAILS

This supplier supports payments for offline orders
  • Letter of Credit : L/C(sight)
  • OT
  • Telegraphic Transfer : T/T
Contact Payment Manager
  • Name : Hong chul Shin

SHIPPING

Shipping from : Republic of Korea
  • 641-66 3.1manse-ro Paltan-myeon, Hwaseong-si, Gyeonggi-do (18578)
INDEX GLOBAL Co., Ltd.

INDEX GLOBAL Co., Ltd.

www.ikkor.com Seller_Mail
  • The person in charge

    HONG CHUL SHIN
  • Address

    641-66 3.1manse-ro Paltan-myeon, Hwaseong-si, Gyeonggi-do (18578)
Introduction
∙ Company Overview Under the slogan "Add Luxury to your buildings", Index Global provides the best products at the best price. We produce exterior wall finishing materials, interior wall finishing materials, floor reinforcements, waterproofing materials, and colorful paints, and export them to various countries around the world. ∙ Factory Information "Delivering the best products to customers as quickly as possible" We have a production facility that can produce 15,000 tons of products per year with the latest automated equipment and the best quality control system to make high-quality products. ∙ Our Service Fastest delivery time, customer-oriented quality policy, competitive price, product warranty, 3 new products every year, new product presentation, demonstration, regular meetings with customers to expand the market, semi-finished products can be supplied upon customer's request. ∙ Our Policy (Company Policy), etc. "I won't take your money if it's not sweet" is a street vendor's pride. We are customer-oriented, quality-oriented, and human-centered, putting customer satisfaction and customer interests first. We are also growing by communicating with customers to make the best products.
  • Business Type :
    Manufacturer
  • Main Product :
    STONE TEXTURED PAINT,STONE EFFECT PAINT
  • Established :
    2010-05-01
  • Total Annual Revenue :
    3~4 billion (KRW)
  • Total Employees :
    11~50 people

R&D CERTIFICATE

COMPANY ENVIRONMENT

Please suggest a variety of your ideas such as design, impact, enhancements, etc

Captcha Required
   

Please enter the text on the left image to prevent automatic input.

0 / 4000

질문이 없습니다.

CUSTOMER REVIEWS (0)

Max 1 files, 20Mb limit per attachment

Captcha Required
   

Please enter the text on the left image to prevent automatic input.

At least 10~1000 characters.

0/ 1000

TRADE EXPERIENCE

  • Total revenue
    3~4 billion (KRW)
  • Total export revenue (previous year in USD)
    380
  • Number of foreign trade employees
    11~50 people

COMPARISON TO SIMILAR ITEMS more

  • No Items
supplier level
GOLD GOLD
INDEX GLOBAL Co., Ltd. Seller's Store
Seller's Store url
  • Response Level
      41% ~ 50%
  • Supplier Level
      1~5 billion (KRW)
  • Transaction Level
      less than 5
SUPPLIER BEST
  • Interior Finishing Materials - Travertino the finest interior finishing material made in Korea
  • Caribbean Coat for External Wall a best-quality spray paint that produces a marble-like texture